• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat punto key programming 500 Key Fob Won't Work

A key fob from fiat keys 500 is a handy way to unlock the doors and get started the car. There are many reasons why the fob may stop working. This includes a dead coin-battery, water damage, receiver modules issues, and interference.

This listing is for a NEW replacement fiat panda key replacement Flip Key Remote that looks like the Ilco brand. It must be professionally programmed (click here to find local automotive locksmiths). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most common reason for your 500 key fob not functioning. Modern key fobs come with a limited operating range, and must be within some feet of the vehicle to operate. If you are far from your vehicle and press the key fob button the car won't be able to respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this occurs then replace the battery for your coin-cell (Part Number CR2032) by a new one of a trusted brand such as Panasonic Duracell or Energizer. You can find them in the local hardware store or on the internet.

After you've replaced the coin cell battery you can test it by standing next to your fiat panda key (Suggested Webpage) 500 and pressing the buttons. The car will blink its parking lights, and the key fob should be able to operate the lock and unlock switches.

If your key fob still isn't working after replacing the battery, it may be water damage which is preventing it from connecting to the module inside your vehicle. Water damage can occur in a number of ways, ranging from small splashes to submerging the fob in salt water at the beach. If you suspect that your fob was exposed to water, put it in a dry rice bag to draw the moisture out. If this doesn't work, you will need to have the fob changed by an auto locksmith or dealer.

Water Damage

Water damage can occur if you submerge the fob in the ocean, or wash it in a machine. Saltwater is particularly dangerous to the circuit board of the fob, causing it to short out and eventually die. It's not good to soak the fob in water however, don't give it up if you accidentally drop it in water or forget to take it out of your pocket.

Take the battery off first. Clean the electronic chip with isopropyl or a similar product and dry it thoroughly before replacing the battery. Check the fob again to check if it's working. If the key doesn't function, it may need to be programmed again. This is typically done by a dealer or professional auto locksmith.

If the key you have is older and is not programmed to work with your vehicle then you'll need to replace it completely. This is a straightforward process that can be handled by a professional automotive locksmith. The locksmith will have to cut the key to match the ignition of your vehicle. The locksmith will also need to reprogram your fob into the vehicle's system. This is a simple and cost-effective procedure that can usually be completed within the same day.

Receiver Module Issues

Your 500 key fob might not work because it's out of range. The remote's range is of 30 feet, which means when you're too far from your car, it won't respond to your commands. It can be solved by moving closer to your vehicle until it begins responding.

If you've replaced the coin battery (commonly called"button" or "button" or "watch") and your fob still won't work It could be because of an internal circuit board issue. In the majority of cases, reprogramming your fob will solve the problem. You can find directions on how to do this for most vehicles by searching YouTube or reading the owner's manual.

It may be necessary to replace the metal clips that hold the coin batteries in their place. If they lose tension it could prevent your coin battery from being properly seated and cause your remote to malfunction.

In rare cases the fob might become desync'd with your vehicle due to software problems or hardware issues. This can be a major headache, but you can usually resolve this issue by visiting an auto locksmith to have them reprogram your fob for you. In certain situations they might need to reinstall the program in your body control module too.

Interference

Interference can also cause the key fob to not be able to receive or transmit signals. This could occur if the key fob is close to the radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. Other reasons why the key fob might not function include a weak connection to the buttons, damage to the internal chip or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to solve the issue (e.g. You may have a faulty 500 receiver module after you've tried replacing the battery, reprogramming or using a spare key fob. The receiver module is situated under the dash and is able to pick up the radio frequency signals from the key fob. It converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy way to reset every single system on board in your 500 and include the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Reconnect the battery. This will remove any residual electricity and restart the car's computers, which could allow you to the key fob to function again. If the problem persists you should speak with an experienced technician. They can identify the exact cause of any issues.