• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Replacement Door Handles

The handles on your doors wear out with time and require to be replaced. In this case, it is crucial that the new handles match the exact dimensions of the handle that was previously used.

The three measurements to check are the top screw's location the lever and key hole dimensions. Refer to the size guide for help with this.

Inline Lever/Lever

A lever/lever handle is a modern-day door handle designed to work with new or replacement doors. This type door handle is offered in a wide range of styles & finishes. A number of manufacturers make this handle including Avocet, ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/composite Door handles (Glamorouslengths.com) are made of sturdy materials and are suitable for doors with multi-point locks that require a heavy duty design. The handles for upvc windows are inline and run off the same spindle and screw fixings so they are easily installed on new or existing uPVC/Composite doors.

The design of the sprung lever allows the handle to be positioned and angled to ensure a comfortable experience and is suitable for all users. The handle has been endurance-tested to 200,000 cycles. This helps ensure that the quality of finish and performance is maintained over time. The sprung lever can be reduced to accommodate a wider range of locks. This is particularly beneficial in doors with smaller door frames in which the cylinder is further back. A shorter lever can be used for doors that have a latch that can be opened by the thumb located on the inside.

Lever Pad

The lever pad upvc handle is different from the lever handles commonly found on doors. These handles can operate from a single spindle (inline) or independently from both sides using two offset or inline spindles (pad). They are typically used on UPVC double glazing window handle glazed doors. They are available in a variety of variations and finishes.

The handles have been tested to the minimum of 200k cycles and are available in a variety of finishes, including White, Silver, Chrome & Gold. The finish is BS EN 1670 Grade 5 and is resistant to corrosion. This provides the handle with an outstanding performance and long-lasting durability for the purpose it was designed for.

All of the UPVC lever pad designs are supplied with a spindle and screws which allow them to be put on a new or existing uPVC door. The backplate fixing centres of 211mm allow for a larger handle, which can often be a benefit when replacing a faulty or worn multi-point door lock mechanism. The handle levers are spring-loaded, which solves the issue of handles hanging out of their horizontal position when they are not being used.

It is crucial to ensure that the dimensions of the PZ for both the multipoint lock and the uPVC doors when selecting a replacement UPVC spindle and handle. This measurement can also be called 'handle centre or cylinder centre'. It is important for matching the correct handles.

When you have the right PZ size you will then need to ensure that the handle lever pads and push pads are of a suitable shape for the American with Disabilities Act (ADA) compatible handles you need for your doors. These are typically of a round or square shape with an internal lever and an external push pad.

The majority of UPVC Lever Pads we offer are sprung. This means they return to a horizontal position when not in use instead of hanging, and possibly sticking in the frame. This helps prevent the draughts and cold air from entering a property. The majority of UPVC lever pad style handles are available in left and right handed models that allow them to be installed on either side of the doors.

Euro Cylinder

Cylinder locks are found on uPVC and other types of doors. They work by using a key that unlock a cylinder case that then reveals pins which can be aligned with the pins in the lock body and allowing them to turn the cam, thereby opening the door. Euro cylinders can be fitted with up to six pins with both internal and external doors typically requiring different levels of security.

Choosing the right cylinder is crucial; it depends on how your door and handle are used. For instance, exterior doors should be fitted with a more secure cylinder while doors inside can be secured using a standard cylinder. Certain cylinders are equipped with additional features that increase security, such as anti-drill or anti bump properties.

A euro cylinder must be properly measured to ensure it's the correct size for your door. The cylinder should be measured from the hole for fixing screws in the middle to the end of the cylinder, including the thumb turn if you have one. It is recommended to do this while the lock is in place, but in the event that this is not feasible, you can take it off and take it off to measure. It is important to avoid having a cylinder that extends beyond the handle or escutcheon. This could make it vulnerable to lock snapping attacks.

The design of the latest cylinders comes with anti-drilling as well as bump resistance features. These features are designed to minimize the chances of an attack by forcing the cylinder to rotate in the opposite direction. This helps deflect the attack and ensure your doors are secure.

There are also cylinders that are made to withstand snapping. This is a typical attack on cylinders. A specially designed tool is used to break the break line of the lock and the front of the cylinder is snapped off. This is faster and more straightforward than opening a multipoint lock and leaves little evidence of a burglary, which could hinder the insurance claim.

Spring Cassette

This spring cassette is found within the base plate of the door handle. It provides a sprung solution to help return the multipoint lock handles to their resting position after use. There was a time when these types of handle did not have a spring integrated into them, and as a result, they tend to droop or drop when the locking mechanism is removed. This component is the most effective way to fix this problem. It also helps prevent your door from becoming stuck in either the closed or open position since they are difficult to close manually.

These spring cassettes were created to be used with sprung multipoint lock. They will not fit handles that are not sprung, and you will have to cut a hole into your backplate for them to fit. (Please look at the image for a technical diagram). These cassettes can be used as a replacement to broken or missing cassettes on the backplate of upvc sliding door handle door handles. They are sold as one unit. They have a square-cut out that is able to accommodate an 8mm shaft.

These spring cassettes provide an excellent value solution to the issue of door handles that have become sagging. They are easy to fit and will extend the life span of your uPVC doors. For more information on our wide range of uPVC spares and accessories please feel free to get in contact with our team. We are on hand to help and happy to provide professional advice.