• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat 500 locked keys in car 500 Key Fob Won't Work

A key fob from fiat 500 locked keys in car 500 makes it easy to open doors and start your vehicle. There are a myriad of reasons the fob may stop working. This includes a dead coin-battery and water damage, as well as problems with receiver modules, as well as interference.

This listing is for a NEW replacement fiat replacement car keys Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to find local automotive locksmiths). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob doesn't work is an inactive battery. Modern key fobs operate with a limited range of operation, and must be within a few feet of the vehicle in order to function. If you are far from your vehicle, and you press the key fob button, the car won't be able to respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this occurs, replace the coin-cell battery (Part Number CR2032) by a fresh one of a reputable brand such as Panasonic Duracell or Energizer. You can typically find them in your local hardware store or online.

You can test the battery of your coin-cell by pressing the buttons while you are standing close to your fiat 500 car key 500. The car will blink its parking lights, and the key fob should work the lock and unlock switches.

If your fob's key doesn't work even after replacing the battery, it may be water damage which prevents it from communicating with the module inside your vehicle. Water damage can happen in a number of ways, from the slightest splash to submerging your fob in salt water at the beach. If you suspect that your fob has been exposed to water, place it in a bag of rice to draw out the moisture. If this doesn't work, you will need to have your fob reset by an auto locksmith or a dealer.

Water Damage

While the fob has some rubber seals to keep water out of the chip's electronic circuit, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short, and eventually die. The fob getting wet is not an ideal choice, but if you drop it in the water in a cup or fail to take it out of your pocket before you run the washing machine, don't give up hope.

Take the battery off first. Before replacing the battery, clean the electronic chip using isopropyl, or a similar product. Next check the fob to verify if it is working. If the fob doesn't work then it might need to be changed. This is usually handled by an auto locksmith or dealer.

If the key is older and hasn't been programmed to your car It is likely that it needs to be replaced completely. This is a simple process that can be handled by a professional automotive locksmith. The locksmith must cut the key to match the ignition of your vehicle. They'll also need to reprogram the fob in your vehicle's system. This is a quick and inexpensive process that can usually be completed within the same day.

Receiver Module Issues

One of the main reasons why your 500 key fob might stop functioning is that it's out of range. The remote's range is of 30 feet, so should you be too far away from your vehicle it will not respond to your commands. This can be easily fixed by moving closer to your vehicle until it starts responding.

If you've replaced the battery in your coin (commonly called"button" or "button" or "watch") and the fob isn't working it could be due to an internal circuit board problem. In most cases, reprogramming the fob will fix the issue. You can find instructions on how to do this for most vehicles by searching YouTube or checking out the owner's manual.

It is possible to replace the clips made of metal that hold the coin batteries in their place. If they loose tension it could hinder the coin battery from sitting properly, and this will cause your remote to malfunction.

In rare instances, the fob may become desync'd with your vehicle due to software or hardware issues. This can be a major headache, but you can usually fix it by visiting an auto locksmith to reprogram your fob. In some instances it is possible that the software will require reinstallation to your body control modules.

Interference

In addition to a dead battery on a coin the key fob could not be receiving or transmitting a signal due to interference. This can occur when the keyfob is in close proximity to a radio transmitter like a cell phone or radar detector. The key fob could not work due to a poor connection to the buttons or water damage, or damage to the internal chips.

If your key fob suddenly stopped working, or you've tried everything at home to fix it (e.g. You might have a damaged 500 receiver module in the event that you've tried replacing the battery, reprogramming or using a spare key fob. The receiver module, which is located beneath the dashboard, receives radio frequency signals from your key fob. It then converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy way to reset all of the on-board systems in your 500 keys, including the key fob. Disconnect the battery 12 volt for about 15 minutes, by taking off the negative cable first then the positive cable. Then, reconnect the battery. This will clear any residual electricity, and allow you to restart the computer in your car. This can help get your key fob to work again. If the problem persists you should seek out a certified technician. They can identify the root of any problems.