• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

how to get a spare subaru key to Change a Subaru Spare Key

Call a locksmith if you lose your subaru key programmer key. Locksmiths are usually able to cut keys for you at a lower cost than the dealer.

Subaru car keys are generally either intelligent "push-to-start" fob remote keys or plain keys made of metal. The Fob key has an embedded chip that will need to be reprogrammed.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It can also open the trunk of your vehicle or the lift gate. The remotes use the keypad in your car to connect with your vehicle's computer system.

Subaru models include a less well-known feature called PIN Code Access. This lets you make a unique sequence of numbers to start and open your car. If you own a more recent Subaru Forester, Outback, Crosstrek, WRX, WRX STI or Impreza that comes with this feature, make sure you check the owner's manual for instructions on how to make use of it.

If your keys stop functioning, there's a good possibility that the battery in the key fob is dead. The first thing to ensure is that the battery is in good condition You can do this using a handheld remote tester or an ordinary multimeter in your home garage.

The next step is to take the circuit board that controls the transmitter from the key fob, and then look at it. There will be one or two sets of 8 numbers. Note the first set so you can remember it. After that you can put the key fob back together and you'll be ready to start programming it at home. The procedure varies based on the year and model of your car. However, it is usually simple enough to complete yourself.

Key Fobs

Subaru's latest models come with key fobs which not only unlock doors but also activate lights, lock the gas cap, and even start the car. This last feature is particularly helpful if you've been at the gas station only to find that your car won't start because the battery in the key fob died.

It doesn't matter if your Subaru is old or new, it's likely that the key fob is able to be replaced with minimal difficulty. It's important to keep in mind that models with a high level of technological sophistication might require a trip to the dealership. With some effort and time, you can make your own replacement key fob.

Begin by opening the case, and then examining the circuit board of the transmitter. (Instructions on how to open the case are usually provided in the owner's guide). It should contain two or three sets of serial numbers each one of which is 8 digits long. Keep the first set of numbers handy for later references.

Then, get into your driver's seat and close all the doors. Turn the key to start your vehicle and then switch off after ten revolutions. Press the lock button of your key fob, then open the door. This will ensure whether your doors are operating properly. Then, close the door and remove the key from the ignition. You should hear your vehicle sound again, signalling that the key fob has been programmed.

Ignition System

The key battery could be dead if your Subaru keys don't work as they should. You can replace the key fob battery on your own if are familiar with the procedure. The replacement of the battery is affordable and simple to locate. If the key fob isn't responding to your commands there could be an issue with a different cause. It's recommended that you go to a dealer to obtain a spare key. They'll ensure that the key is genuine Subaru key that is under warranty, and that it is programmed to your vehicle. This is far safer and more convenient than purchasing an aftermarket key from a retailer online.

You can also ask the dealer cut a new subaru key key if you provide them with your VIN number and proof of ownership. They'll use this information to program the new key in order to be accepted by the immobilizer. This is a more complicated process than cutting a key, and the dealer will charge more for it.

Once the new key has been programmed, it is possible to switch it to your existing key. It will take only five seconds to insert the second key, which is why it's important to keep an operational key in your pocket. You can remove the key after the security light has stopped flashing and test it.

Battery Replacement

Subaru fobs are extremely useful because they can switch on the power windows and sunroof of your car with just a single button press. The battery in your Subaru fob isn't built to last forever, and will have to be replaced eventually. Fortunately, replacing the battery is a simple process that you can do yourself with the help of this quick guide from Capitol Subaru.

To begin, you'll need to locate the small crevice in the seam that separates the front and back of your key fob. Utilizing a small flathead screwdriver, you can pop the seam open and reveal a small compartment inside which is the battery. Install the new battery and make sure it is facing the right way. Remove the old one. After everything is in place and in place, you can use your new key fob to lock or unlock your vehicle effortlessly!

It's always best to have an additional set of keys available, especially if you've lost yours or it's not functioning properly. A new key can be bought at your local auto dealership or you can request one cut by an locksmith. Whatever you choose, it's essential to get your key fob functioning properly as soon as possible to ensure you drive in a safe manner!