• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to fix door hinge - More Information and facts, a Loose Door Hinge

The majority of homeowners can fix a loose hinge. However, if the holes for screws are smashed and can't hold screws, you might need to put in dowels and wood glue before you can reinstall the hinge.

Before you do that though you should clean off any the surface rust. This will aid in keeping the dowels in their place and provide a solid foundation to hold onto.

Take off the Hinges

Many hinges for doors can be removed, which makes it easier to move a door from one side of the frame to the other or take the entire door off when needed. Anyone who is patient can remove the hinges however, you must know what to do.

If the hinges have been painted you'll need to take off it prior to trying to remove the pins. If you don't, the paint could peel off and scratch your double glazing door hinges when you try to lift it. To break the paint seal, place the hinges in a stainless steel dish and fill the pan with water until the hinges are completely submerged. The hinges should remain in the pan for approximately 30 minutes. The heat of the water will soften the paint, making it easier to remove.

After the pins have been loosen then you can remove the hinges from the door and frame. You can use a screwdriver to get the job done, but it is recommended to employ a magnetic screwdriver to complete this task. This type of screwdriver has been specifically designed to take out metal screws and help you get the job done much faster.

It is a good idea to spray lubricant on the hinges prior to attempting to remove them. A simple lubricant can help you accelerate the process and also remove the pins and screws more easily. This kind of lubricant can be found at most hardware stores and home improvement stores.

Keep in mind that the number of hinges you will need will vary depending on the door's type and the configurations. Doors with a heavier core and solid-core will need more hinges, while hollow-core doors with a lighter weight might only require two or three hinges.

It is also crucial to know the various types of hinges to determine which ones will best suit your needs. Exterior hinges are designed to withstand the weight of a door, whereas interior hinges need to be able to handle heavier loads.

Reattaching the Hinges

Over time, a door hinge can loosen and begin to slide or hang crookedly. This could be a problem however, it's usually simple to solve. In most cases an easy tightening of the screw will solve the problem. If the screw holes have been stripped out, it can be difficult to do. There is a trick to make these holes back to their original size that uses a wood dowel.

Begin by drilling out the hole from the previous one using a drill bit that is similar to the size of the new screw (typically 3/8"). Then, use wood glue and dowels made of wood to fill the hole. The dowel should be cut to a length the same as the screw to ensure a tight fit. Then, reinstall the screw and tighten it to the desired degree of tightness. If the door still has a tendency to bind, then add another dowel to the gap and repeat the process. Close the door slowly after each adjustment to ensure the clearances around the perimeter are correct.

You can also use a wooden plug instead of the dowel. This is also a viable option however it will take a bit longer to install. You can insert a piece of wood that has been whittled down to the proper size. If you don't have a tool for woodworking, you can also use toothpicks or wooden matches as well.

After you've reinstalled your new screw then use a countersink to make the hole for the screw's head smaller so that it does not rub against the edge of the door when it is opened and closed. This will make it much easier to tighten the screws after installing hinges.

Once you have reinstalled the hinge, make sure to grease it with a dry lubricant to ensure that it doesn't get stuck in the future. You can use products like PB Blaster and Liquid Wrench. Apply a thin layer and allow it to soak into the hinge barrel for about 15 minutes.

Refinishing the Hinges

If you're unsure whether to replace your hinges, try a few easy fixes. The first step is to make sure that the screws securing the hinge plate to the door and frame are tight. If they're loose, tighten them with a screwdriver or power drill. Be careful not to tighten your screws so tight that they start to create gaps at the trim joints, or worse, strip the threads.

If the issue is that the hinge plates are breaking they can be reattached to the plates by putting wood glue on the back of them and then inserting wooden dowels or toothpicks in the holes. The dowels or toothpicks provide a solid base for the screws and to prevent the plates from shifting when you drive them into position. Let the glue dry before reattaching the hinge.

The screws can also be smashed or gone. This can be corrected by replacing the screws. Make sure you use the correct drill bit for the size of the screw hole to avoid drilling into other parts of the hinge or jamb.

After you've reattached your hinge shut the upvc door hinge and look at the gap between the frame and the door. The gap should be about the thickness of a penny or less if an old door was not hung correctly. This shouldn't be a problem as long as the hinges are installed correctly.

If you notice that the hinges are still loose, try adding the thicker shim of the hinge between the hinge plate and the mounting surface, to create some extra space. You can also try removing the hinge pin from the problem hinge and pounding it with a hammer to make it tighter or using the hinge pin from a different angle altogether. You can also grease your hinges with mineral oil or jojoba to decrease friction and keep them in their place. Periodically lubricating your hinges can aid in keeping them from becoming stiff or squeaky, and will also prolong their lifespan.

Cleaning the Hinges

The friction stay hinges caused by the hinge's constant motion attracts dust particles. These particles may get stuck and accumulate over time in the moving parts of door hinges if they are not maintained and cleaned regularly. As a result the hinge becomes stiff and creaky, and its appearance can get worse. Regular cleaning, lubrication, and inspection can help preserve the integrity of a hinge on a door and ensure its proper function.

Examine the hinges for signs of rust accumulation. If the rust has corroded to the point of damaging the surface of the hinge barrel or screw holes, you'll require replacement of the hinges. If you can save the hinges, begin by brushing off loose rust using steel wool and wire brushes. Then, apply a rust remover from a commercial store or a homemade solution, such as lemon juice to the hinge. Let the solution that removes rust remain on the hinges for a few minutes to penetrate and dissolve the remaining rust.

If you do not want to spend cost and time to replace hinges, simply tightening the screws can bring back the hinge's functionality. It is possible to attach dowel or shim made of wood to the hinge in the event that the screws have been degraded. Wooden dowels come in round rods that vary in sizes and lengths. You can buy them online, at stores selling woodworking supplies and home improvement centers.

A shim could also be made from a piece of metal or plastic, depending on the kind of hinge you've got. To make a dowel cut a piece made of wooden dowel or another sturdy material to the desired size. You can then dip a dowel into the adhesive of a carpenter and insert it in the hole. The glue will hold the dowel securely in the position.

Before cleaning the hinges, lay down a cloth or towel to protect your flooring from spills. Once the area is protected, proceed to clean the hinges with an absorbent sponge or a soft cloth dipped in a mild cleaner or vinegar to remove the build-up of dirt, grime and tarnish. A small brush or toothbrush can be used to access difficult-to-reach places in crevices and difficult places.